Sunday, July 29, 2012

Unlock DB2020 SE phones tagalog procedure


ito naman ang procedure:

1: buksan ang setool software at piliin ang tamang model ng SE.

2: punta muna sa settings at lagyan ng check ang signmode lang.

3: balik naman sa main at click ang recovery > hintayin mag success.

4: punta naman sa empty fill tab at ilagay uli ang tamang model ng SE.

5: lagyan ng GDFS na makikita sa setool folder mismo,piliin ang SSW na GDFS

6: pagkatapos mailagay ang GDFS click mo na flash at hintayin matapos.

7: pagkatapos ma write ang GDFS tanggalin ito at palitan naman ng EROM

8: dapat ang EROM na ilagay same sa CID ng phone na ginagawa nyo.

9: click nyo na flash uli at hintayin matapos ito.

10: lagyan ng batery at simcard kung ok na ang phone

Thursday, July 26, 2012

Samsung S5253 insert sim. Solution here!


try ko siya program so ginawa ko factory reset ko muna

using *2767*3855# pero same problem ganun parin siya

so decide ako na buksan ang unit at nakita ko tanggal

ang isang pin socket ginawa ko tinanggalan ko muna yung

sheilding case sa tapat ng ala ng pin socket

eto yung picture.





kumuha ako ng sim pin sa scrap board ng nokia

eto yung picture nung nalagyan ko na ng pin






jumper ko yung isang pin

na natanggal, eto yung nakita ko jumper ko yung pin niya






after kong nalagyan ng jumper at pin assemble ko na yung unit

ayun sapul tinanggap na yung sim at may signal na

eto yung finish product.


Samsung S5670 Vodafone Unlock Done z3x


s5670 lock sa vodafone

procedure:


1. Enter code *#7284# - choise phone usb.
2. Enter code *#9090# - choise usb diag. (or *#197328640# -> 9 -> 4 -> usb diag ) then reboot phone
3. Connect cable. Setup drivers




done

iPod 4G strike again no light 1 shot jumper TESTED


model : ipod 4g
history : wet
problem : no light
action taken : jumper

SCREENSHOT

apply this simple jumper kung mkkta mo may moist cya remove and make jumper pwde led lang pang jumper mo para mabilis pa

\

after 1 shot jumper done......

Nokia 1616-2 no power and lights done. Solution here


ito po ung ginawa ko........




ito napo ung unit ok na........

SAMSUNG A777 Unlock done. Solution here!


SETOOL activated
micro USB

PROCEDURE:
1. Make sure battery is full charged
2. Power On phone and enter code *#782872# (Qualcomm Mode)
3. Connect your phone to the computer.
4. Your computer will pop-up with new hardware wizard. Don't let it search automatically for on your computer.

UNLOCKING
Rescan ports
press Read UnlockCodes
a message pop-up in your SGTOOL GUI to dial in your phone this codes *#782872#
& press ok
wait till process done...

SCREEN SHOOT


Motorola Mb501 Passcode DOne hard reset


procedure

1.Press the menu key and turn on the phone.

2.Press the 'camera' key and 'power' key simultaneously and hold till the Moto batwing screen goes away and you will see a message on the screen to release the 'camera' key.

3.User will see option to get into recovery mode.

4.Press Volume down key to get into recovery mode.

5.Once in the recovery mode, tap on the right lower corner of the touchscreen(might have to tap a few times).

6.'Motorola system recovery' menu will come up.

7.User can use the mini pad or tough screen and select wipe data/factory reset to do a factory reset.

8.Select 'ok' at the lower left corner once the intended menu item has been selected.

9.Use the mini pad to scroll up and select reboot system now

10.Press OK

Nokia 6020 no power DONE! Solution Here!


UNIT:NOKIA 6020


PROBLEM: NO POWER


ACTION:
FULL FLASH version 5.20
kaso may error sa flashing
reheat ko kunti flash ic
flash uli done
sincya d ko na picture ang logs


factory reset nalang




done:



bayad barya lang po sa umaga

Nokia 5530 vibrate only done..


1st step: SW ko muna sa mataas na V 40.0.003..pag try ko nawala po ang vibrate dead na.. kinabahan ako kc sundalo ang may ari.
so search ako d2 sa tinapay. my nakita ako parehas kmi ng prob..so ang ginawa nya blik nya ang original nyang product code..

2nd step: nag download din ako ng firmware na same code, reprogram ulit
so nag vibrate ulit.. pero stil no luck..
search me ulit d2 sa tinapay..
so it0 ang nakita ko

3rd step


so apply ko ito,
still no luck mga bos,
search me ulit at ito nman ang nakita ko

4rth step


ang ginawa ko ne reheat ko lang mga bos..
kc d pa me masyadong hasa sa pag bunot ng mga pisa..
so assemble ko na kc ibabalik ko na sa cus2mer kung sundalo pag no luck pa rin

ng matapos ko e assemble mga bos at e try ko,,

ito ang nakita ko..
ALHAMDULILLAH


ok na sya,,

para maka siguro ako
info ko sya sa mxkey
ito ang logs..
MXKEY [MxKey Team HTI PLUS Flasher Interface 1], SN: C085E4E4
Using device: HTI, FW ver: 00.50, SN: 01002EA4
Connection status: UHCI:HUB:USB 2.00 (Full-speed)
Driver: WinUSB, ver: 3.5.1.0*
Module ver: 1.0.0.20814(05-05-2012), Library ver: 1.0.0.14060(05-05-2012)
CMT Data :
SYSTEM ASIC ID: 000000010000022600010006400C192101051105 [RAPIDOYAWE ver: 1.1x]
EM0 ID: 00000296
EM1 ID: 00000B22
PUBLIC ID: 0F500106C982005200189396A2E5CD41EE73BAC3
ASIC MODE ID: 00
ROOT KEY HASH: B8C3ADECFC997FCD8081D3DEAF870B8C
ROM ID: 4B9B75103E691FF8
*SecondaryBoot: RAPIDOv11_2nd.fg [BB5] *version: 12.2.0 revision: 2.0 size: 0x3B80
*Supported Ids: 0003192101001203, 000C192101001203, 4003192101001203, 400C192101001203, 0003192101002003, 000C192101002003, 4003192101002003, 400C192101002003, 4003192101011103, 400C192101011103, 4003192101021103, 400C192101021103, 4003192101031103, 400C192101031103, 4003192101011105, 400C192101011105, 400C192101021105, 400C192101031105, 4003192101051103, 400C192101051103, 400C192101051105, 4003192101051105
eBB5ProtocolType: NEW
TransmissionMode: DDR&TX2
Storage0: 0000 0000 *- 0000 0000 *type: RAM, asic:CMT*
Storage1: FFFF 0000 *- 0000 0000 *type: MMC, asic:CMT*
Storage2: 0020 0040 *- 0000 0031 [ST *NAND KAT00F00RA] type: FLASH,NOR, asic:CMT*
Storage3: 0000 0001 *- 0000 0000 [unused/removed] type: FLASH,NOR, asic:CMT*
Storage4: 0020 0040 *- 0000 0031 [ST *NAND KAT00F00RA] type: FLASH,MuxOneNAND, asic:CMT*
Suggested algorithm: XSR 1.5
*Algorithm: RAPIDOv11_XSR15_alg.fg [XSR 1.5] *version: 12.2.0 revision: 2.0 size: 0x8B45D
*Supported Ids: 0003192101001203, 000C192101001203, 4003192101001203, 400C192101001203, 0003192101002003, 000C192101002003, 4003192101002003, 400C192101002003, 4003192101011103, 400C192101011103, 4003192101021103, 400C192101021103, 4003192101031103, 400C192101031103, 4003192101011105, 400C192101011105, 400C192101021105, 400C192101031105, 4003192101051103, 400C192101051103, 400C192101051105, 4003192101051105
TransmissionMode: DDR&TX2
FUR: Adding Asic CMT as client OK
CMT PAPUBKEYS HASH: F2B05364E563A348608C1C3C9E54FE42AAAA1ACF
Selected firmware certificate matched.
Original Imei: 35802203909212
Original Product code: 0578163
Bluetooth ID: A87E331EA36C
SIMLOCK PA identifier:
*[0] PA_SL3
*
Phone type: RM-504 (Nokia 5530 XpressMusic)
SW version: V ICPR72_10w29_tube1 24-05-11 RM-504 (c) Nokia*
ApeCoreSw: V 40.0.003
Imei plain: 35802203909212-9
Product code: 0578163
Battery voltage: 4633 mV, current: 27 mA
Language Pack:
- not available.




SLPA ver[4]: PA_SL3/PA_SIMLOC30 (15 digit NCK)
warning: avoid SW Downgrade & manual erase to this phone !
*
SIMLOCK seems to be valid
SUPERDONGLE_KEY seems to be valid
CMLA_KEY seems to be valid
WMDRM_PD seems to be valid
SIMLOCK_TEST passed
SECURITY_TEST passed
*
*
Imei net: 358022039092129
Version: SIMLOCK SERVER
Counter: 0/3, 0/10
*
CONFIG_DATA: 2440700000000000
PROFILE_BITS: 0000000000000000
*
BLOCK1: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK2: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK3: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK4: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK5: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK6: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK7: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
FULL FACTORY... OK
USER DATA... OK
LEAVE FACTORY... OK
SERVICE CENTER... OK
SOFTWARE UPGRADE... OK
PRODUCTION TUNING... OK
Reset User Code (to default:12345) ... OK
Completed in 2.172 s

Huawei U7510 lock code done procedure with picture. Solution here!


Huawei U7510 lock code done procedure with picture

action taken :
HARD reset

ilagay ang code na 1234 (code error) pindutin ang end key lalabas ang pinka menu ng phone
at itype ito




pindutin ang pinaka gitnang button

lalabas ang TEST mode pumunta sa number 8



buksan




buksan ulit








nokia 110 security code, done..


problem: security code
solution: re- program

1-open cyclone
2-select bb5
3-load flash file
4-insert modified usb (note: yan po ung kadalasan natin gamit n usb cable sa motorola v3, sundan n lang po kulay kung saan ihihinang)
5-click write all flash images

done...

 



Samsung S5300 unlocking solved. Solution here!

info hit direct unlock solved



-----------------------------------------------------------------------------------
Platform: Samsung Broadcom
Selected port: COM19
Selected model: GT-S5300
Detected phone model: GT-S5300
SW Version: S5300DXLF2/S5300OLBLE1/S5300DXLE1/S5300DXLF2
HW Version: GT-S5300ZKAXTE
Phone IMEI A: 353170-05-278281-4
Firmware compiled date: Fri Jun 22 19:08:20 KST 2012
Android version: 2.3.6 (GINGERBREAD)
-----------------------------------------------------------------------------------
Platform: Samsung Broadcom
Selected port: COM19
Selected model: GT-S5300
Detected phone model: GT-S5300
SW Version: S5300DXLF2/S5300OLBLE1/S5300DXLE1/S5300DXLF2
HW Version: GT-S5300ZKAXTE
Phone IMEI A: 353170-05-278281-4
Firmware compiled date: Fri Jun 22 19:08:20 KST 2012
Android version: 2.3.6 (GINGERBREAD)
Unlocking phone...
Phone is successfully unlocked
Please, restart phone to apply changes